Recommended
Tools And Supplies:
felt unicorn pieces
doll eyes
embroidery thread
craft wire
mane fiber
toy filling
needle and thread
small sharp scissors
stuffing tool (chop stick or tooth pick)

Make Your Own Tiny Felt Unicorn!
Begin by making sure you have all of the pieces of felt needed for your tiny felt unicorn.

We will start by installing doll eyes into the two main body pieces of the unicorn. To make the eyes uniform on both sides, the best method is to match together both pieces of felt and poke a small hole through the felt right where you want to install the doll eyes. By poking through both pieces at the same time you will ensure that the eyes sit in the same spot on both sides of the body.
Insert the back post of the doll eye through the front of the felt. Fasten the included small plastic washer to the back of the eye, at the inside of the fabric with the flat side of the washer facing downward. An alternative to using plastic doll eyes would be to embroider the eyes in with some thread by placing a few very small stitches. You could also use beads, or even paint them on.

To create ears trim along the dotted lines (as per the pattern) between the head and ear. Fold the felt forward and place a few small stitches at the inside of the head.
Pin the “Under Body” piece to one of the “Body” pieces, matching the felt at the legs. Fold the very back of the “Under Body” piece upward matching the edges of felt together to the back of the rump. Begin stitching the edges together with a short tight stitch. Stitch moving downwards towards the back leg, working along the edge until you reach the front of the chest.


Pin and sew the opposite side of the Body to the “Under Body” piece, ending once again at the chest. This time continue sewing upwards to the front of the face. Pin the face piece to one side of the main body starting at the nose. Continue sewing along one side attaching at the edges of the felt. Switch to a running stitch at the ear, continuing past until you reach the end of the Face piece. Tie of your thread at the inside of the horse..

Add wire to the inside of the mini horse! Begin by cutting a small length of pipe cleaner to place inside each leg. How I determine length is by holding the wire up to the horse’s legs and bending into the correct shape. I snip off the end of the wire after comparing and shaping.
TIP: fold up the very ends of the wire to make them easier to insert into the small legs.


Fold the wire in half (the shape of an upside down “V”) and insert one end each into the front and back legs. There will be one folded piece for the front legs, and one for the back. Next stuff the legs with toy stuffing. This can get tricky! The trick is to use very tiny amounts at a time, balled up as small as you can get them. Push the pieces down into the legs using a toothpick or similar object.

Stuff the legs right to the tops. Now to go back and begin and sewing the opposite side of the head shut. Begin by tying off your thread to the inside of the face right by the nose and begin stitching once again from the nose towards the back of the head.
When you’ve reached about halfway begin stuffing the face and head. Continue sewing downward stuffing into the head, then chest.
When you’ve reached the end of the “Face” piece you should only have a small space left open for stuffing. Stuff the rest of the body full and sew the opening shut. Do not tie off the thread! Train it out at the end of the rump and leave the thread hanging. You will use this to attach the tail at the back of the rump.

To sew in the tail, I lay several strands next to each other, and another longer piece vertical to the rest. I then tie the longer piece into a knot right in the middle of the the other strands, essentially tying them together in a bundle. Fold in half at the knot and you’ve got a tail. Now all that needs doing is to sew it in place at the knot.



Next we will fold the tiny unicorn horn in half across the length, knot our thread to the inside and sew down the side of one edge creating a cylindrical shape (the horn!). Leave the thread trailing as to use to sew the horn into place and the mane as well. stuff the horn with a very small piece of stuffing rolled into a ball. Stuff it into the horn with either the end of your scissors or a tooth pick. Stuff the horn to just the opening.

Pin the horn into place on the unicorns head. For the first stitch I like to send the needle and thread straight down into the unicorns head, out under the chin, then directly back up through one side of the bottom of the horn.


after the first stitch you will place very small stitches around the base of the horn to hold it into place. The end stitch will go through the base of the horn and out just between the ears.

Now to sew the mane into place! Simply lay many strands of wool across the head of the horse and stitch them in place
with a hand sewing back stitch, laying the stitches from just between the ears down the middle of the back.



Pin wings in place on either side of the horse. We will use the string jointing method to attach the wings, by sending your needle from the back of the mane to straight out through the side of the unicorn and out of the wing.

Send the needle and thread back in through the wing to create a small stitch. The needle should go straight through the unicorn and out of the opposite wing.

You will place stitch after stitch, placing each stitch on top ofthe first moving the needle back and forth through the unicorn’s body. Tie off your thread behind one of the wings.

I hope you enjoyed sewing your tiny unicorn! I’d love to see what your finished project looks like!

